View RT9183H-18CG_4201958.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

RT9183
Ultra Low Dropout 1.5A Linear Regulator
General Description
The RT9183 series are high performance linear voltage regulators that provide ultra low-dropout voltage, high output current with low ground current. It operates from an input of 2.3V to 5.5V and provides output current up to 1.5A thus is suitable to drive digital circuits requiring low voltage at high currents. The RT9183 has superior regulation over variations in line and load. Also it provides fast respond to step changes in load. Other features include over-current and overtemperature protection. The adjustable version has enable pin to reduce power consumption in shutdown mode. The devices are available in fixed output voltages of 1.2V to 3.3V with 0.1V per step and as an adjustable device with a 0.8V reference voltage. The RT9183 regulators are available in 3-lead SOT-223 and TO-263 packages (fixed output only for the 3-lead option). Also available are 5-lead TO-263, TO-252 and fused SOP-8 packages with two external resistors to set the output voltage ranges from 0.8V to 4.5V.
Features
330mV Dropout @ 1.5A 380uA Low Ground Pin Current Excellent Line and Load Regulation 0.1uA Quiescent Current in Shutdown Mode Guaranteed 1.5A Output Current Fixed Output Voltages : 1.2V to 3.3V Adjustable Output Voltage from 0.8V to 4.5V Over-Temperature/Over-Current Protection RoHS Compliant and 100% Lead (Pb)-Free
Ordering Information
RT9183 Package Type G : SOT-223 GF : SOT-223 (F-Type) S : SOP-8 L: TO-252 LF : TO-252 (F-Type) M : TO-263 M5 : TO-263-5 Operating Temperature Range P : Pb Free with Commercial Standard G : Green (Halogen Free with Commercial Standard) Output Voltage Defauit : Adjustable 12 : 1.2V 13 : 1.3V : 32 : 3.2V 33 : 3.3V Only for SOP-8 and TO-263-5 H : Chip Enable High L : Chip Enable Low
Note : Richtek Pb-free and Green products are : RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020. Suitable for use in SnPb or Pb-free soldering processes. 100%matte tin (Sn) plating.
Applications
Battery-Powered Equipment Mother Board/Graphic Card Peripheral Cards PCMCIA Card
DS9183-14 April 2008
www.richtek.com 1
RT9183
Pin Configurations
(TOP VIEW)
1
2
3
1
2
3
1
2
3
1
2
3
VIN
GND (TAB)
VOUT
GND
VOUT (TAB)
VIN
GND (TAB) VIN VOUT
VOUT (TAB) GND VIN
SOT-223
SOT-223 (F-Type)
TO-252
TO-252 (F-Type)
EN VIN VOUT ADJ
2 3 4
8 7 6 5
GND GND GND GND
1 2 3
1 2 3 4 5
SOP-8
VIN VOUT GND(TAB)
EN VIN VOUT ADJ GND(TAB)
TO-263
TO-263-5
Typical Application Circuit
(SOT-223 & TO-263 & TO-252) VIN = 3.3V CIN 10uF VIN RT9183 VOUT GND COUT 10uF VOUT 2.5V, 1.5A
Figure 1. 3.3V to 2.5V Regulator
(SOP-8 & TO-263-5) VIN Enable C 0.1uF VIN EN RT9183 VOUT R1 CIN 10uF GND ADJ R2 COUT 10uF VOUT
VOUT = 0.8 x (1 +
R1 )Volts R2
Note: The value of R2 should be less than 80k to maintain regulation.
Figure 2. Adjustable Operation
www.richtek.com 2 DS9183-14 April 2008
RT9183
(SOP-8 & TO-263-5) VIN Enable C 0.1uF CIN 10uF VIN EN RT9183 VOUT GND ADJ COUT 10uF VOUT
Figure 3. Fixed Operation with SOP-8 and TO-263-5 packages
Functional Pin Description
Pin Name EN VIN GND VOUT ADJ Chip Enable Control Input. Note that the device will be in the unstable state if the pin is not connected. Supply Input. Common Ground. Regulator Output. The output voltage is set by the internal feedback resistors when this pin grounded. If external feedback resistors are applied, the output voltage will be: VOUT = 0.8 x (1 + R1 ) Volts
R2
Pin Function
Function Block Diagram
VIN Current Limit Sensor + 0.8V Reference
Error Amplifier
-
+ VOUT
EN
Shutdown Logic
Thermal Shutdown ADJ Output Mode Comparator
DS9183-14 April 2008
+
100mV GND
www.richtek.com 3
RT9183
Absolute Maximum Ratings
(Note 1) 6V 115C/W 15C/W 135C/W 17C/W 125C/W 20C/W 68C/W 8C/W 75C/W 15C/W 45C/W 8C/W 0.87W 0.74W 0.8W 1.471W 1.333W 2.22W 260C 150C -65C to 150C 2kV 200V Supply Input Voltage -----------------------------------------------------------------------------------------------------Package Thermal Resistance SOT-223, JA ---------------------------------------------------------------------------------------------------------------SOT-223, JC --------------------------------------------------------------------------------------------------------------SOT-223 (F-Type), JA ---------------------------------------------------------------------------------------------------SOT-223 (F-Type), JC ---------------------------------------------------------------------------------------------------SOP-8, JA -----------------------------------------------------------------------------------------------------------------SOP-8, JC -----------------------------------------------------------------------------------------------------------------TO-252, JA ----------------------------------------------------------------------------------------------------------------TO-252, JC ----------------------------------------------------------------------------------------------------------------TO-252 (F-Type), JA -----------------------------------------------------------------------------------------------------TO-252 (F-Type), JC -----------------------------------------------------------------------------------------------------TO-263, JA ----------------------------------------------------------------------------------------------------------------TO-263, JC ----------------------------------------------------------------------------------------------------------------Power Dissipation, PD@TA = 25C SOT-223 --------------------------------------------------------------------------------------------------------------------SOT-223 (F-Type) ---------------------------------------------------------------------------------------------------------SOP-8 -----------------------------------------------------------------------------------------------------------------------TO-252 ----------------------------------------------------------------------------------------------------------------------TO-252 (F-Type) ----------------------------------------------------------------------------------------------------------TO-263 ----------------------------------------------------------------------------------------------------------------------Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------------Junction Temperature ----------------------------------------------------------------------------------------------------Storage Temperature Range -------------------------------------------------------------------------------------------ESD Susceptibility (Note 2) HBM (Human Body Mode) ---------------------------------------------------------------------------------------------MM (Machine Mode) ------------------------------------------------------------------------------------------------------
Recommended Operating Conditions
(Note 3)
Supply Input Voltage ------------------------------------------------------------------------------------------------------ 2.3V to 5.5V Junction Temperature Range -------------------------------------------------------------------------------------------- -40C to 125C
Electrical Characteristics
(VIN = VOUT + 0.7V, CIN =COUT = 10uF (Ceramic), TA = 25C unless otherwise specified)
Parameter Output Voltage Accuracy (Fixed Output Voltage) Output Voltage Range (Adjustable) Quiescent Current Standby Current (Note 6) (Note 7)
Symbol VOUT VOUT_ADJ IQ ISTBY
Test Conditions IOUT = 10mA
Min -2 0.8
Typ 0 -380 0.1
Max +2 4.5 500 1
Units % V uA uA
IOUT = 0mA, Enable VIN = 5.5V, Shutdown
---
To be continued
www.richtek.com 4 DS9183-14 April 2008
RT9183
Parameter Current Limit Dropout Voltage (Note 4) Symbol ILIM IOUT = 0.5A VDROP IOUT = 1.0A IOUT = 1.5A Line Regulation Load Regulation (Note 5) VLINE VLOAD TSD TSD VIL VIH IEN VIN = 5.5V VIN = 5.5V VIN = 5.5V, Enable VOUT + 0.7V < VIN < 5.5V IOUT = 10mA 1mA < IOUT < 1.5A Test Conditions Min 2 ----Typ 3.2 110 220 330 0.035 Max 4.2 300 400 500 0.18 %/V mV Units A
(Fixed Output Voltage) Thermal Shutdown Temperature Thermal Shutdown Hysteresis EN Threshold Logic-Low Voltage Logic-High Voltage Enable Pin Current ADJ Reference Voltage Tolerance Adjust Pin Current Adjust Pin Threshold
----1.8 --
22 170 30 --0.1
45 --0.6 -1
mV C C V uA
VREF IADJ VTH(ADJ) VADJ = VREF
0.784 -0.05
0.8 10 0.1
0.816 100 0.2
V nA V
Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may remain possibility to affect device reliability. Note 2. Devices are ESD sensitive. Handling precaution is recommended. Note 3. The device is not guaranteed to function outside its operating conditions. Note 4. The dropout voltage is defined as VIN -VOUT, which is measured when VOUT is VOUT(NORMAL) - 100mV. Note 5. Regulation is measured at constant junction temperature by using a 20ms current pulse. Devices are tested for load regulation in the load range from 10mA to 1.5A. Note 6. Quiescent, or ground current, is the difference between input and output currents. It is defined by IQ = IIN - IOUT under no load condition (IOUT = 0mA). The total current drawn from the supply is the sum of the load current plus the ground pin current. Note 7. Standby current is the input current drawn by a regulator when the output voltage is disabled by a shutdown signal (VEN >1.8V ). It is measured with VIN = 5.5V. Note 8. JA is measured in natural convection (still air) at TA = 25C with the component mounted on a low effective thermal conductivity test board of JEDEC 51-3 thermal measurement standard. And the copper area of PCB layout is 4mm x 2.5mm on SOT-223, 10mm x 10mm on TO-252, 14mm x 14mm on TO-263 for thermal measurement.
DS9183-14 April 2008
www.richtek.com 5
RT9183
Typical Operating Characteristics
Output Voltage vs. Temperature
1.9
Output Voltage vs. Temperature
2.6
VIN = 5V, RL = CIN = COUT = 10uF (Ceramic,Y5V)
VIN = 5V, RL = CIN = COUT = 10uF (Ceramic,Y5V)
Output Voltage (V)
Output Voltage (V)
RT9183H-18xS
1.85
2.55
1.8
2.5
1.75
2.45
RT9183-25xG
2.4 -50 -25 0 25 50 75 100 125
1.7 -50 -25 0 25 50 75 100 125
Temperature (C)
Temperature (C)
Quiescent Current vs. Temperature
400
Quiescent Current vs. Temperature
400
Quiescent Current (uA) 1
380
Quiescent Current (uA) 1
380
360
360
340
340
320
VIN = 5V, RL = CIN = COUT = 10uF (Ceramic,Y5V)
-50 -25 0 25 50
320
RT9183H-18xS
300
75 100 125
VIN = 5V, RL = CIN = COUT = 10uF (Ceramic,Y5V)
-50 -25 0 25 50
RT9183-25xG
75 100 125
300
Temperature (C)
Temperature (C)
Current Limit vs. Temperature
4
Current Limit vs. Temperature
4
VIN = 5V, CIN = COUT = 10uF(Ceramic,Y5V)
3.8
VIN = 5V, CIN = COUT = 10uF(Ceramic,Y5V)
3.8
Current Limit (A)
3.6
Current Limit (A)
3.6
3.4
3.4
3.2
3.2
RT9183-25xG
3 -50 -25 0 25 50 75 100 125
RT9183L-33xM5
3 -50 -25 0 25 50 75 100 125
Temperature (C)
www.richtek.com 6
Temperature (C)
DS9183-14 April 2008
RT9183
Dropout Voltage Dropout Voltage vs. Load Current
500
500
Dropout Voltage vs. Load Current Dropout Voltage
TJ = 125C
Dropout Voltage (mV) 1
300
Dropout Voltage (mV)
400
TJ = 125C
400
300
TJ = +25C
200
TJ = +25C
200
TJ = -40C
100
TJ = -40C
100
RT9183-25xG
0 0 0.3 0.6 0.9 1.2 1.5
0 0 0.3 0.6 0.9
RT9183L-33xM5
1.2 1.5
Load Current (A)
Load Current (A)
Dropout Voltage vs. Load Current
400
Load Transient Response
COUT = 47uF/Low ESR, ILOAD = 1mA to 750mA
Load Current (A) Output Voltage Deviation(mV)
RT9183H-xS VOUT = 3.3V
TJ= 125C
1 0.5 0
Dropout Voltage (mV)
300
TJ= 25C
200
TJ= -40C
100
20 0 -20 RT9183H-18xS
0 0 0.3 0.6 0.9 1.2 1.5
Load Current (A)
Time (100us/Div)
Load Transient Response
COUT = 47uF/Low ESR, ILOAD = 1mA to 1.5A
Load Transient Regulation
Output Voltage Deviation(mV)
RT9183-12xGF
Load Current (A)
2 1 0 50 0 -50
20 0
Load Current (mA)
Output Voltage Deviation(mV)
500 0
ILOAD = 1mA to 750mA COUT = 47uF/Low ESR
RT9183H-18xS
Time (100us/Div)
Time (100us/Div) www.richtek.com 7
DS9183-14 April 2008
RT9183
Line Transient Regulation
Input Voltage Deviation(V) Input Voltage Deviation(V)
ILOAD = 100mA COUT = 47uF/Low ESR 5 4
Line Transient Response
COUT = 47uF/Low ESR, ILOAD = 100mA
5 4
Output Voltage Deviation(mV)
Output Voltage Deviation(mV)
10 0 -10 RT9183H-18xS
10 0
RT9183-12xGF
Time (100us/Div)
Time (100us/Div)
EN Pin Threshold Voltage vs. EN Pin Shutdown Threshold vs. Temperature
1.1
EN Pin Shutdown Response
CIN = COUT = 10uF (Ceramic,Y5V)
EN Pin Shutdown Threshold Voltage (V) 1 Voltage (V)
EN Voltage (V)
ILOAD = 100mA, VIN = 5V, TA =25C 5 0
1
VOUT Off to On
0.9
Output Voltage (V)
VOUT On to Off
0.8
2 1 0 RT9183H-18xS
RT9183L-33xM5
0.7 -50 -25 0 25 50 75 100 125
Temperature (C)
Time (500us/Div)
Reference Voltage vs. Temperature
0.85
VIN = 5V,CIN = COUT = 10uF (Electrolysis)
Reference Voltage (V)
0.83
0.81
0.79
0.77
RT9183H-xS
0.75 -50 -25 0 25 50 75 100 125
Temperature (C)
www.richtek.com 8
DS9183-14 April 2008
RT9183
Application Information
Like any low-dropout regulator, the RT9183 series requires input and output decoupling capacitors. These capacitors must be correctly selected for good performance (see Capacitor Characteristics Section). Please note that linear regulators with a low dropout voltage have high internal loop gains which require care in guarding against oscillation caused by insufficient decoupling capacitance. Input Capacitor An input capacitance of 10F is required between the device input pin and ground directly (the amount of the capacitance may be increased without limit). The input capacitor MUST be located less than 1 cm from the device to assure input stability (see PCB Layout Section). A lower ESR capacitor allows the use of less capacitance, while higher ESR type (like aluminum electrolytic) require more capacitance. Capacitor types (aluminum, ceramic and tantalum) can be mixed in parallel, but the total equivalent input capacitance/ ESR must be defined as above to stable operation. There are no requirements for the ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be10F over the entire operating temperature range. Output Capacitor The RT9183 is designed specifically to work with very small ceramic output capacitors. The recommended minimum capacitance (temperature characteristics X7R or X5R) are 10F to 47F range with 10m to 25m range ceramic capacitors between each LDO output and GND for transient stability, but it may be increased without limit. Higher capacitance values help to improve transient. The output capacitor's ESR is critical because it forms a zero to provide phase lead which is required for loop stability. No Load Stability The device will remain stable and in regulation with no external load. This is specially important in CMOS RAM keep-alive applications. Input-Output (Dropout) Voltage A regulator's minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. In battery-powered systems, this determines the useful end-of-life battery voltage. Because the device uses a PMOS, its dropout voltage is a function of drain-to-source on-resistance, RDS(ON), multiplied by the load current : VDROPOUT = VIN - VOUT = RDS(ON) x IOUT Current Limit The RT9183 monitors and controls the PMOS' gate voltage, minimum limiting the output current to 2A . The output can be shorted to ground for an indefinite period of time without damaging the part. Short-Circuit Protection The device is short circuit protected and in the event of a peak over-current condition, the short-circuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency. Please refer to the section on thermal information for power dissipation calculations. Capaacitor Characteristics It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. In general, a good tantalum capacitor will show very little capacitance variation with temperature, but a ceramic may not be as good (depending on dielectric type). Aluminum electrolytics also typically have large temperature variation of capacitance value.
DS9183-14 April 2008
www.richtek.com 9
RT9183
Equally important to consider is a capacitor's ESR change with temperature: this is not an issue with ceramics, as their ESR is extremely low. However, it is very important in tantalum and aluminum electrolytic capacitors. Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic capacitors is so severe they may not be feasible for some applications. Ceramic: For values of capacitance in the 10F to 100F range, ceramics are usually larger and more costly than tantalums but give superior AC performance for by-passing high frequency noise because of very low ESR (typically less than 10m). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within 20% of nominal over full operating ratings of temperature and voltage. Of course, they are typically larger and more costly than Z5U/ Y5U types for a given voltage and capacitance. Tantalum: Solid tantalum capacitors are recommended for use on the output because their typical ESR is very close to the ideal value required for loop compensation. They also work well as input capacitors if selected to meet the ESR requirements previously listed. Tantalums also have good temperature stability: a good quality tantalum will typically show a capacitance value that varies less than 10~15% across the full temperature range of 125C to -40C. ESR will vary only about 2X going from the high to low temperature limits. The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if the ESR of the capacitor is near the upper limit of the stability range at room temperature). Aluminum: This capacitor type offers the most capacitance for the money. The disadvantages are that they are larger in physical size, not widely available in surface mount, and have poor AC performance (especially at higher frequencies) due to higher ESR and ESL. Compared by size, the ESR of an aluminum electrolytic is higher than either Tantalum or ceramic, and it also varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50X when going from 25C down to -40C. It should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120Hz, which indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance specified at a higher frequency (between 20kHz and 100kHz) should be used for the device. Derating must be applied to the manufacturer's ESR specification, since it is typically only valid at room temperature. Any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating temperature where ESR is maximum. Thermal Considerations Thermal protection limits power dissipation in RT9183. When the operation junction temperature exceeds 170C, the OTP circuit starts the thermal shutdown function and turns the pass element off. The pass element turns on again after the junction temperature cools by 30C. For continuous operation, do not exceed absolute maximum operation junction temperature 125C. The power dissipation definition in device is : PD = (VIN - VOUT) x IOUT + VIN x IQ
www.richtek.com 10
DS9183-14 April 2008
RT9183
The maximum power dissipation depends on the thermal resistance of IC package, PCB layout, the rate of surroundings airflow and temperature difference between junction to ambient. The maximum power dissipation can be calculated by following formula: PD(MAX) = ( TJ(MAX) - TA ) /JA Where T J(MAX) is the maximum operation junction temperature 125C, TA is the ambient temperature and the JA is the junction to ambient thermal resistance. For recommended operating conditions specification of RT9183, where T J(MAX) is the maximum junction temperature of the die (125C) and TA is the maximum ambient temperature. The junction to ambient thermal resistance (JA is layout dependent) for SOT-223 package is 115C/W, SOT-223 package (F-Type) is 135C/W, SOP-8 package is 125C/W, TO-252 package is 68C/ W, TO-252 package (F-Type) is 75C/W and TO-263 package is 45C/W on standard JEDEC 51-3 thermal test board. The maximum power dissipation depends on operating ambient temperature for fixed TJ(MAX) and thermal resistance JA. For RT9183 packages, the Figure 4 of derating curves allows the designer to see the effect of rising ambient temperature on the maximum power allowed.
2400 2000 1600 1200
PCB Layout Good board layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors MUST be directly connected to the input, output, and ground pins of the device using traces which have no other currents flowing through them. The best way to do this is to layout CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a"single point ground" . It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane were used at the ground points of the device and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and it's capacitors fixed the problem. Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. Optimum performance can only be achieved when the device is mounted on a PC board according to the diagram below :
GND
Maximum power dissipation (mW)
TO-263 TO-252 (F-Type)
TO-252
SOT-223
800 400 0 0 25 50 75 100 125
+
+
ADJ
SOT-223 (F-Type) SOP-8
EN
VOUT
Figure 4
GND VIN GND
SOP-8 Board Layout
DS9183-14 April 2008
+
Ambient temperature (C) ( )
www.richtek.com 11
RT9183
Adjustable Operation The adjustable version of the RT9183 has an output voltage range of 0.8V to 4.5V. The output voltage is set by the ratio of two external resistors as shown in Figure 2. The value of R2 should be less than 80k to maintain regulation. In critical applications, small voltage drop is caused by the resistance (RT) of PC traces between the ground pin of the device and the return pin of R2 (See Figure 5 shown on next page). Note that the voltage drop across the external PC trace will add to the output voltage of the device. Optimum regulation will be obtained at the point where the return pin of R2 is connected to the ground pin of the device directly.
(SOP-8 & TO-263-5) VIN Enable C 0.1uF CIN 10uF VIN EN RT9183 VOUT R1 GND ADJ RT R2 VOUT COUT 10uF
Figure 5. Return Pin of External Resistor Connection Referring to Figure 3 the fixed voltage versions for both SOP-8 and TO-263-5 packages, the ADJ pin is the input to the error amplifier and MUST be tied the ground pin of the device directly otherwise it will be in the unstable state if the pin voltage more than 0.1V with respect to the ground pin itself.
www.richtek.com 12
DS9183-14 April 2008
RT9183
Outline Dimension
D D1
H
C
B
L e e
L1
A b
A1
Symbol A A1 b B C D D1 e H L L1
Dimensions In Millimeters Min 1.450 0.020 0.610 3.302 6.706 6.299 2.896 2.261 0.229 1.550 0.800 Max 1.803 0.100 0.787 3.708 7.290 6.706 3.150 2.362 0.330 1.950 1.100
Dimensions In Inches Min 0.057 0.0008 0.024 0.130 0.264 0.248 0.114 0.089 0.009 0.061 0.009 Max 0.071 0.0047 0.031 0.146 0.287 0.264 0.124 0.093 0.013 0.077 0.013
3-Lead SOT-223 Surface Mount Package
DS9183-14 April 2008
www.richtek.com 13
RT9183
A
H M
J
B
F
C I D
Dimensions In Millimeters Symbol Min A B C D F H I J M 4.801 3.810 1.346 0.330 1.194 0.170 0.050 5.791 0.400 Max 5.004 3.988 1.753 0.508 1.346 0.254 0.254 6.200 1.270
Dimensions In Inches Min 0.189 0.150 0.053 0.013 0.047 0.007 0.002 0.228 0.016 Max 0.197 0.157 0.069 0.020 0.053 0.010 0.010 0.244 0.050
8-Lead SOP Plastic Package
www.richtek.com 14
DS9183-14 April 2008
RT9183
D D1 B T V E L1 S C U R
L3 b1 b e b2 L2
A
Symbol A B b b1 b2 C D D1 E e L1 L2 L3 U V R S T
Dimensions In Millimeters Min 2.184 0.889 0.508 Max 2.388 2.032 0.889
Dimensions In Inches Min 0.086 0.035 0.020 Max 0.094 0.080 0.035
1.016 Ref. 0.457 0.457 6.350 5.207 5.334 2.108 9.398 0.584 0.584 6.731 5.461 6.223 2.438 10.414
0.040 Ref. 0.018 0.018 0.250 0.205 0.210 0.083 0.370 0.023 0.023 0.265 0.215 0.245 0.096 0.410
0.508 Ref. 0.635 1.016
0.020 Ref. 0.025 0.040
3.810 Ref. 3.048 Ref. 0.200 2.500 0.500 0.850 3.400 0.850
0.150 Ref. 0.120 Ref. 0.008 0.098 0.020 0.033 0.134 0.033
3-Lead TO-252 Surface Mount Package
DS9183-14 April 2008
www.richtek.com 15
RT9183
D B C U
V E L1
b1 L2 e b b2
A
Symbol A B b b1 b2 C D E e L1 L2 U V
Dimensions In Millimeters Min 4.064 1.143 0.660 1.143 0.305 1.143 9.652 8.128 2.286 14.605 2.286 Max 4.826 1.676 0.914 1.397 0.584 1.397 10.668 9.652 2.794 15.875 2.794
Dimensions In Inches Min 0.160 0.045 0.026 0.045 0.012 0.045 0.380 0.320 0.090 0.575 0.090 Max 0.190 0.066 0.036 0.055 0.023 0.055 0.420 0.380 0.110 0.625 0.110
6.223 Ref. 7.620 Ref.
0.245 Ref. 0.300 Ref.
3-Lead TO- 263 Surface Mount
www.richtek.com 16
DS9183-14 April 2008
RT9183
C
D B
U
V E L1
L2 e b b2
A
Symbol A B b b2 C D E e L1 L2 U V
Dimensions In Millimeters Min 4.064 1.143 0.660 0.305 1.143 9.652 8.128 1.524 14.605 2.286 Max 4.826 1.676 0.914 0.584 1.397 10.668 9.652 1.829 15.875 2.794
Dimensions In Inches Min 0.160 0.045 0.026 0.012 0.045 0.380 0.320 0.060 0.575 0.090 Max 0.190 0.066 0.036 0.023 0.055 0.420 0.380 0.072 0.625 0.110
6.223 Ref. 7.620 Ref.
0.245 Ref. 0.300 Ref.
5-Lead TO-263 Plastic Surface Mount Package
Richtek Technology Corporation
Headquarter 5F, No. 20, Taiyuen Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Fax: (8863)5526611
Richtek Technology Corporation
Taipei Office (Marketing) 8F, No. 137, Lane 235, Paochiao Road, Hsintien City Taipei County, Taiwan, R.O.C. Tel: (8862)89191466 Fax: (8862)89191465 Email: marketing@richtek.com
DS9183-14 April 2008
www.richtek.com 17

▲Up To Search▲

Price & Availability of RT9183H-18CG

	To Download RT9183H-18CG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .